Full Fat Audio - FFA - 8004 G2 DSP
A completely new amplifier design from FFA. Designed to give exceptional audio for live performance sound. FFA-8004 G2 DSP amplifier's provide a cost effective solution for sound system design.
Ideal for permanent installation or temporary sound. The DSP software has been designed to be functional and quick to use and has a familiar feel to that of a mixing console.
The software runs on all platforms - PC or MAC/ IPAD based software. The DSP is accessed by Neutrik Ethercon and connected using an Ethernet network direct to a personal computer (MAC/ IPAD or PC) or via an Ethernet Hub or wireless router.The DSP has 4 analogue audio input’s or 1 pair of selectable AES/EBU digital inputs.
There are 6 analogue audio output channels - 4 assigned to the FFA-8004 power amplifier and 2 assigned to a pair of male XLR connection on the rear panel of the amplifier.
These extra processed outputs could be used to design a 3 way stereo system of bass, mid and high frequency where the 2 outputs drive a 2 channel bass amplifier or used as a 2 channel DSP for any signal that requires control.
The DSP features a broad band input compressor and 2 stage output signal limiter. The signal limiting allows precise system protection or contains environmental noise.
The DSP is fully password protected and has options to disable functionality. This gives the designer a tool to keep interference from unauthorised persons whom may change parameters which could either damage the loudspeaker system or exceed set environmental noise levels.
Features at a glance:
PC , Mac , ipad, VR1 Wall remote control
FATWARE - Ethernet control
Useful toolbox for environmental noise control
DSP has four audio inputs / 6 audio outputs
Matrix mix all 4 audio inputs and 6 outputs
2 band Dynamic EQ on 4 inputs and 6 outputs
6dB/Octave – 48dB Octave high and low pass filters
Comprehensive limiting functions on 6 outputs
6 band parametric EQ on inputs
8 band parametric EQ on outputs
Compressor / limiter on all four audio inputs
Up to 1.3 seconds delay on inputs and outputs
AES EBU DIGITAL INPUT
DSP bypass switch to allow analogue amplifier operation
Suitable Applications:
Exceptional sound for all loudspeaker systems – bass is powerful, fast and tight – mids and high frequency are natural and open.
Stage monitor performance will give super clear vocal sound.
Vocal and high frequency inteligibility for large scale systems is superb.
Ideal for any night venue, theatre, cruise ship, AV systems, Cinemas, Conferences temporary audio installation at music festivals.
Power Ratings - FFA - 8004 G2 DSP - 4 x 1000W 8 Ohm, 4 x 2000W 4 Ohm
Gain - 32 dB
THD - THD+N Typical 0.05 4% Ohm 1kHz
Frequency Response 20Hz - 20kHz +- 0.5d B
Controls - 40 Point Potentiometer per channel, power on switch
Indicators - signal green = -20dB, signal yellow = -3dB, red signal = clip, signal red protect = over current, low AC mains or 3 sec. mute on power up
Load Protection - DC on output, precision clip limiter circuit
Amplifier Protection - Short circuit, current overload, thermal shutdown, high frequency stability circuit
Audio Signal Inputs - Balanced Neutrik® Female XLR input connected Pin 1 - GND, Pin 2 - Hot +, Pin 3 - Cold - .
Audio Power Outputs - Neutrik® speakON each channel. Channels 1 and 3 output speakON utilises 2+ and 2- connection to allow use of 4 core loudspeaker cable for bi amp loudspeaker system. For example stage monitor system
Power Requirement - 1 x Neutrik® 20A powerCON connector 1 x 16A 230 VAC Circuit. Power range 185V-230VAC 120V (configured at factory)
System Cooling - High CFM 80mm fan with proportional signal speed control. Rear to front airflow
Dimensions - 88mm Height x 483mm Width x 510mm Depth. Includes rear rack support. 19" rack mount enclosure
Weight - 10 kg
020 8659 2558
