Full Fat Audio - FFA 2004 G2 DSP Amplifier

Full Fat Audio - FFA 2004 G2 DSP Amplifier

FFA-2004 G2 DSP amplifier's provide a cost effective solution for sound system design.Ideal for permanent installation or temporary sound.

The DSP software has been designed to be functional and quick to use and has a familiar feel to that of a mixing console.

The software runs on all platforms - PC or MAC/ IPAD based software.

The DSP is accessed by Neutrik Ethercon and connected using an Ethernet network direct to a personal computer (MAC/ IPAD or PC) or via an Ethernet Hub or wireless router.

The DSP has 4 analogue audio input’s or 1 pair of selectable AES/EBU digital inputs.

There are 6 analogue audio output channels - 4 assigned to the FFA-2004 power amplifier and 2 assigned to a pair of male XLR connection on the rear panel of the amplifier.

These extra processed outputs could be used to design a 3 way stereo system of bass, mid and high frequency where the 2 outputs drive a 2 channel bass amplifier or used as a 2 channel DSP for any signal that requires control.

The DSP features a broad band input compressor and 2 stage output signal limiter. The signal limiting allows precise system protection or contains environmental noise.

The DSP is fully password protected and has options to disable functionality. This gives the designer a tool to keep interference from unauthorised persons whom may change parameters which could either damage the loudspeaker system or exceed set environmental noise levels.

Suitable Applications:

Small full range loudspeaker for example 5"-10" + 1" driver compliment, smaller bass units 8" -10" drivers.

Public address systems of any kind – peripheral systems in larger installations. AV systems.

High power mid range and HF drivers in multi way installed sound or touring sound systems.

Smaller stage monitors bi amp or full range

Features at a glance:

Exceptional sound quality

High Power efficiency and cool running

Rugged Tour class Aluminium construction

Light weight - 8 kg

FFA Class D PWM

High current switch mode power supply designed to give continuous power

Superb limiter

4 XLR analogue audio inputs

Bi amp Neutrik® speakON outputs

Neutrik® powerCON power input

PSU soft start

Hand built & designed in Hertfordshire, England

5 year factory warranty

Power ratings - FFA - 2004 G2 DSP - 4 x 250W 8 Ohm load, 4 x 500W 4 Ohm load 4 x 1000W 2 Ohm load

Gain - 32dB

THD - THD Typical 0.03 4 Ohm 1kHz THD+N

Frequenxy Response - 20Hz - 20kHz +- 0.5dB

Controls - 40 Point Potentiometer per channel, power on switch

Indicators - signal green = -20dB, signal yellow = -3dB, red signal = clip, signal red protect = over current, low AC mains or 3 sec. mute on power up

Load Protection - DC on output, side chain TCA clip limiter circuit

Amplifier Protection - Short circuit, current overload, thermal shutdown, high frequency stability circuit

Audio Signal Inputs - Balanced Neutrik® Female XLR input connected Pin 1 - GND, Pin 2 - Hot +, Pin 3 - Cold - . XLR Male signal throughput each channel

Audio Signal Outputs - Neutrik® speakON each channel. Channels 1 and 3 output speakON utilises 2+ and 2- connection to allow use of 4 core loudspeaker cable for bi amp loudspeaker system for example stage monitor system

Power Requirements - 1 x Neutrik® 20A powerCON connector 1 x 16A 230 VAC Circuit. Power range 185V-230VAC 120V (configured at factory)

System Cooling - High CFM 80mm fan with proportional signal speed control. Rear to front airflow

Dimensions - 88mm Height x 483mm Width x 510mm Depth. Includes rear rack support. 19" rack mount enclosure

Weight - 9kg